FILING COMMANDS

Overview

The Proteus layout module makes use of the following file types:

  • Project Files (.PDSPRJ)
  • Project Clips (.PDSCLIP)
  • Panels (.PDSPNL)
  • Workspace Files (.WORKSPACE)
  • Region Files (.RGN), legacy support only, replaced by project clips.
  • Library Files (.LIB)
  • Style Files (.STY)
  • Output Job Profiles (.POPROF)

All data from the pcb is collated and stored as part of the Proteus project file with extension 'PDSPRJ'. This is a compound file containing the schematic data, the layout data, the project database and potentially other simulation related files. Backup copies made when saving over an existing file are prefixed with 'Backup of...'.

Information about which modules are open in Proteus (e.g. Schematic, Bill of Materials and Layout) together with their positions on your monitor(s) and which frames they are in are stored in the project workspace file. This allows you to return to the same project state when you reload a project.

Region files have the extension 'RGN' and were the mechanism used by older versions of Proteus to move a region of a layout into another board. They are supported for import only: use the Import Project Clip command with the file type selector set to V7 Region Files, as described under Import Region below. New work should use project clips instead.

Symbol and package libraries have the extension 'LIB', while the trace and pad style file has extension STY. Output Job Manager profiles are stored as portable POPROF files that can be shared between projects, workstations and colleagues.

Starting a New Project

To start a new design you need to create a new Proteus project. You do this by invoking the New Project Wizard either from the home page or from the file menu. This wizard guides you through the setup of your next Proteus project. There is a start page in which you specify the project name and destination directory and then potentially four main screens, for the schematic, the PCB, the layer stackup and the firmware.

Schematic

When creating a schematic check the box at the top of the screen and then select the template on which you want to base the schematic. Those provided by Labcenter basically contain different sizes of work area, although you can customise and save your own templates from within the schematic capture module.

The schematic template selection page of the New Project Wizard

PCB Layout

If you are creating a PCB check the box at the top of the screen and select from the available templates. PCB templates contain pre-defined board edges, mounting holes and a full set of technology data (design rules, layers in use, default units, etc.) As with schematic, you can customise and save your own templates from within the PCB layout module.

The PCB layout template selection page of the New Project Wizard

This screen will only be presented to you if you have a license for one of the Proteus PCB design products.

Layer Stackup

When you have opted to create a PCB the wizard follows the template page with a layer stackup page, so that the physical construction of the board is settled before layout begins. This is the same form as the Set Layer Stackup command on the Technology menu, with the Stackup Wizard available to set the copper layer count and the board construction style. Your settings are applied as you move forward through the wizard, so the drill spans are in place by the time the project opens.

If the layer stack is already defined in the PCB template you chose on the previous page then this page will simply show the template stackup, ready for you to accept or adjust. See Defining a Layer Stack for a full description of the form.

Firmware

If you are creating an embedded design and want to simulate your firmware, check the create firmware box at the top of the screen and then select your controller and compiler using the combo boxes. If selected, the quick start files checkbox will generate a skeleton firmware project for you and configure project settings for compilation.

The firmware page of the New Project Wizard, with the controller family, controller and compiler selectors

Creating a firmware project requires a schematic in order to simulate so you cannot proceed from this screen if you opted not to create a schematic earlier in the wizard.

The combo boxes on this screen are license aware so you cannot create a firmware project for a controller than you cannot simulate in Proteus.

There is also a summary page at the end allowing you to review your setup before the wizard exits and generates the project files.

Loading an Existing Project

Loading an existing project can be done in four ways:

  • From the command prompt as in: PDS.EXE <my_project>
  • By clicking on the Open Project button on the Proteus home page.
  • By using the Open Project command on the File Menu inside Proteus.
  • By double clicking the PDSPRJ  file in Windows Explorer.

Importing a Legacy Project

Older versions of Proteus typically contained several files such as a DSN file for schematic and a LYT file for layout. The Import Wizard on the home page and File Menu is used to bring these projects into Proteus.

To import a legacy project

Launch the import wizard.

The Import Legacy Design button in the Start section of the Proteus home page

Browse for the old schematic (.dsn file)

Browsing for the old schematic DSN file in the import wizard

If a PCB file (.lyt file) is associated with the schematic it will automatically appear in the Layout field. If there is no layout file associated with the schematic then leave this field blank.

The Layout field of the import wizard filled in with the associated LYT file

If an old VSMStudio file (.vsmp) with the same name as the schematic exists in the same directory it will automatically appear in the VSM Studio edit box. If the wrong VSMP file appears or there is no corresponding VSMP file then either browse for the file or leave blank.

The VSM Studio field of the import wizard filled in with the associated VSMP file

The project name and path are taken from the filestem and location of the schematic being imported. You can change this if required from the fields at the bottom of the dialogue box.

The project name and path fields at the bottom of the import wizard

If you change the path for a VSM project then you will need to manually change the PROGRAM property of the microcontroller, otherwise your simulation will fail.

When you are finished use the import button to create the imported project.

Saving the Project

You can save your Project when quitting via the Exit command, or at any other time, using the Save Project command. In both cases it is saved to the same file from which it was loaded. The old version will be prefixed with the text ‘Backup of’.

The Save As command allows you to save the Project to a different file.

Import Region

The Export Region command is deprecated and has been replaced by Project Clips.

Legacy region files can be imported via the Import Project Clip command and then adjusting the file type selector to V7 Region Files. After import you should then immediately create a project clip from the imported circuitry.

The Files of type selector in the import dialogue set to V7 Region Files

Setting the file type selector to V7 Region Files

Import / Export Project Clip

Project clips (.PDSCLIP) can be imported and placed on the schematic/layout. If you are importing a clip which contains both a schematic and a layout portion you must import and place inside the Schematic Capture module.

Project clips can be exported by first dragging a selection box around the area in the schematic and/or layout that you want to export and then invoking the Export Project Clip command  on the right click context menu or on the File Menu.

The Export Project Clip command on the File menu

The Export Project Clip command on the File menu

Export is only available for valid selections: please refer to the rules for project clips.

See Also:

Project Clips

Backups and Last Loaded Files

Proteus includes a comprehensive backup and recovery system to help protect your work in the event of a crash or application hang. In particular, the auto-save and recovery mechanism provides a last stop guarantee should the worst happen and the program crashes. This is discussed in detail in the topic linked below:

See Also:

Backup and Recovery

 While Proteus includes significant protection and recovery from application faults we strongly recommend that you organise and maintain your own backup procedures to complement those provided by the software.