Replicate

Overview

The Replicate dialogue duplicates the current selection at defined step intervals. In Cartesian mode (the default) copies are placed at specified X/Y offsets; in Polar mode (enabled via the View Menu) the form is titled Radial Replicate and copies are placed at angular intervals around a radial origin. You must first highlight the objects you wish to replicate.

The controls are arranged in two groups, Duplication and Re-Annotation.

See Also:

Replicate

Offset and Separate

These two radio buttons in the Duplication group decide how the step values are interpreted.

Offset means that the step values represent the absolute distance from the position of the original to each successive copy. The Relative to control is not applicable in this mode.

Separate means that the step values represent the gap between the edges of the original and each successive copy. The Relative to control then selects which bounds are used to determine the object edges.

Relative to

Selects the reference point or bounds used for positioning. The available options depend on the spacing mode and the type of objects selected.

Separate Mode

In Separate mode the Relative to control selects which bounds are used to calculate the gap between copies.

Mode

Available When

Bounds Used for Gap Calculation

Object Extremity

Always

Overall object area including non-copper elements such as silkscreen.

Copper Extremity

Always

Copper-only bounds, excluding silkscreen and other non-electrical features.

Courtyard

Single component with a courtyard defined

The occupancy or courtyard bounds of the component footprint.

Offset Mode

In Offset mode the Relative to control is disabled in Cartesian mode. In Radial mode it selects the reference point from which the radial distance is measured.

Mode

Available When

Reference Point

Selection Centre

Always

Centre of the combined selection bounds.

Pin 1 Centre

Single component

Centre of pin 1 of the selected component.

Component Centre

Single component

Centre of the component bounds.

Pad Centre

Single pad

Centre of the selected pad.

Mouse Position

Context menu invocation only

The cursor position at the time the command was invoked.

No. of Copies

The number of duplicates to create (1 to 100). When a Bind To target is selected, this is locked to 1.

Cartesian Replicate

In Cartesian mode (the default) the dialogue presents X and Y step fields.

X-Step

The horizontal distance between copies. In Offset mode this is the direct copy-to-copy distance. In Separate mode this is the gap between the edges of adjacent copies in X.

Y-Step

The vertical distance between copies. It operates identically to X-Step but in the vertical axis.

Radial Replicate

When Polar coordinates are active (View Menu), the dialogue presents radial controls instead of Cartesian X/Y steps. Separate mode is not currently available for radial replication.

Angular Step

The angle in degrees between each successive copy (-180 to 180). Copies are rotated around the specified radial origin.

Radial Offset/Separation

The radial distance from the origin to the reference point of each copy. This is pre-calculated from the current selection position and can be adjusted to move copies closer to or further from the origin.

Radial Origin

The centre point for the angular rotation.

  • Current Origin, the false origin if set, otherwise the world origin.
  • Output Origin, the CADCAM output origin.
  • Database Origin, the absolute world origin (0,0).

Re-Annotation

These controls apply to both Cartesian and Radial modes and are used when replicating blocks of circuitry that have corresponding schematic subcircuits.

Bind To

Lists sibling schematic sheets or modules that share the same circuit topology as the selected components. When a target is selected, each copy is bound to that sheet so that its components are associated with the correct schematic instance. It is only available when the selection belongs to a non-root child sheet with unplaced siblings. When a binding target is selected, the number of copies is locked to one and the increment is disabled.

Increment

The numeric step applied to component designators for each copy. For example, an increment of 100 turns R1, R2 in the original into R101, R102 in the first copy, R201, R202 in the second copy, and so on (range 0 to 10000).