ICON REFERENCE

This chart names every button you will meet in the VSM Studio application module, together with the command it runs, its keyboard shortcut where it has one, and a short description of what it does. The same artwork appears on the toolbars, on the menus and on the context menus of the project tree.

A few pictures serve more than one command, and each command is listed separately below. The icons shown here are the light theme artwork; VSM Studio also ships a dark variant of most of its icons and switches between the two automatically when you change the application theme.

Project and Files

These commands appear on the Project menu, on the Firmware toolbar and on the context menus of the project tree. The same picture is used for Delete Project and for Remove Peripheral.

Icon Command Shortcut Description

Create Project

Create Project   Create a new firmware project.

Delete Project

Delete Project   Delete a firmware project.

Add New File

Add New File CTRL+ALT+N Add a new source file to the firmware project.

Add Files

Add Files CTRL+ALT+A Add or copy existing files to the firmware project.

Remove File

Remove File   Remove source file from the firmware project.

Open File

Open File CTRL+ALT+O Open a source file.

Close File

Close File CTRL+F4 Close source file.

Print File

Print File CTRL+P Print source file.

Add Peripheral

Add Peripheral   Add an external peripheral block to the project.

Enable/Disable Peripheral

Enable/Disable Peripheral   Enable or disable this peripheral.

Remove Peripheral

Remove Peripheral   Remove a peripheral block from the project.

Reload Driver

Reload Driver   Reload the driver/descriptor from its XML file.

Add IoT Control

Add IoT Control   Add an IoT panel control to the project.

Project Settings

Project Settings   Edit the firmware project's build settings.

Build

These commands appear on the Build menu and on the Build toolbar, and they act on the focused project. Build Project and Compile File share the same picture.

Icon Command Shortcut Description

Build Project

Build Project CTRL+F7 Build current firmware project.

Rebuild Project

Rebuild Project ALT+F7 Rebuild the current firmware project.

Stop Build

Stop Build ESC Abort current build.

Clean Project

Clean Project CTRL+F6 Delete all output & intermediate files generated by compiler.

Compile File

Compile File   Compile one file.

Upload

Upload CTRL+F8 Write program to the hardware board.

Editing

These commands appear on the Edit menu and on the Edit toolbar, and they act on the source file in the active editor tab.

Icon Command Shortcut Description

Undo

Undo CTRL+Z Undo last action.

Redo

Redo CTRL+Y Redo last action.

Find

Find CTRL+F Find text.

Replace

Replace CTRL+H Replace text.

Cut

Cut CTRL+X Cut the current selection's contents to the clipboard.

Copy

Copy CTRL+C Copy the current selection's contents to the clipboard.

Paste

Paste CTRL+V Paste the clipboard's contents into the current selection.

Debug and Simulation

These commands appear on the Debug menu. The stepping commands are also available from the source editor while the simulation is paused.

Icon Command Shortcut Description

Start VSM Debugging

Start VSM Debugging CTRL+F12 Start Debugging.

Pause VSM Debugging

Pause VSM Debugging PAUSE Pause Debugging.

Stop VSM Debugging

Stop VSM Debugging SHIFT+PAUSE Stop Debugging.

Run Simulation

Run Simulation F12 Run the simulation.

Step Over Source Line

Step Over Source Line F10 Step over the current Function/Subroutine.

Step Into Source Line

Step Into Source Line F11 Step into the current Function/Subroutine.

Step Out from Source Line

Step Out from Source Line CTRL+F11 Step out of the current Function/Subroutine.

Run To Source Line

Run To Source Line CTRL+F10 Execute until the current cursor position is reached.

Configure Diagnostics

Configure Diagnostics   Configure what is recorded in the simulation log.

The Animation Control Panel

The animation control panel sits at the foot of the schematic and carries its own buttons. The transport buttons take no keyboard shortcut of their own, since the equivalent Debug menu commands carry them. At the right of the panel a button reports the state of the simulation log and opens the log when you click it; its picture tells you the most serious item the log holds.

Icon Command Shortcut Description

Run

Run   Run the simulation.

Advance

Advance   Advance the simulation by one animation frame.

Pause

Pause   Pause the simulation, or start up at time 0 if stopped.

Stop

Stop   Stop the simulation.

Multimeter

Multimeter   Show the multimeter.

Scope

Scope   Show the oscilloscope.

Simulation log, messages

Simulation log, messages   The log holds messages only. Click to display the simulation log.

Simulation log, warnings

Simulation log, warnings   The log holds one or more warnings. Click to display the simulation log.

Simulation log, errors

Simulation log, errors   The log holds one or more errors. Click to display the simulation log.

System and Help

The two configuration commands sit on the System menu and the Breakpoints command on the Edit menu. All three carry the same picture, so read the command name on the menu rather than the button. The three help commands likewise share one picture and open the manual for the module you name.

Icon Command Shortcut Description

Compilers Configuration

Compilers Configuration   Displays Compilers configuration dialogue.

Editor Configuration

Editor Configuration   Displays Editor configuration dialogue.

Breakpoints

Breakpoints SHIFT+F9 Open Breakpoints window.

VSM Studio Help

VSM Studio Help   Show the VSM Studio Help.

Visual Designer Help

Visual Designer Help   Show the Visual Designer Help.

IoT Builder Help

IoT Builder Help   Show the IoT Builder Help.

Framework File Commands

These four buttons belong to the application frame rather than to VSM Studio, and you will find them at the left of the application toolbar in every module of the suite. They act on the Proteus project as a whole, not on the firmware project. Open Project and Close Project use the same pictures as the Open File and Close File commands above.

Icon Command Shortcut Description

New Project

New Project CTRL+N Start a new project.

Open Project

Open Project CTRL+O Open an existing project.

Save Project

Save Project CTRL+S Save project with same name.

Close Project

Close Project   Close the project.

See Also:

Guided Tour

Testing and Debugging